Glossary

Fastener terms, explained.

Plain-language definitions for the standards, materials and parts buyers meet every day — written to be quoted, not just skimmed.

50 terms DIN · ISO · GB/T
50 terms
Bolts

Anchor bolt

A bolt designed to be fixed into concrete or masonry so that equipment, frames or structures can be attached to it.

Read definition
Finishes

Black oxide

A conversion coating that darkens steel by forming a thin black oxide layer on the surface, with mild corrosion protection when it is oiled or waxed.

Read definition
Pins & Rivets

Blind rivet

A rivet that can be installed from one side of a joint, where pulling a mandrel deforms the rivet body to clamp the parts together.

Read definition
Nuts

Cap nut

A hex nut with a closed domed top that covers the bolt end, protecting the thread and giving a finished appearance.

Read definition
Materials

Carbon steel

Steel whose main alloying element is carbon, used for most general-purpose fasteners and supplied in several strength grades.

Read definition
Bolts

Carriage bolt

A bolt with a smooth domed head and a square neck that bites into the material to stop rotation, tightened from the nut side.

Read definition
Nuts

Castle nut

A hex nut with slots cut across the top, locked in place by a cotter pin passing through the bolt.

Read definition
Anchors

Chemical anchor

An anchor that bonds a threaded rod or stud into a drilled hole using a chemical adhesive, usually a two-part resin.

Read definition
Washers

Circlip

A split ring that fits into a groove on a shaft or in a bore to locate or retain a component in the axial direction.

Read definition
Threads

Coarse thread

The standard metric thread series with the largest pitch for a given diameter, used for general fastening.

Read definition
Screws

Countersunk screw

A screw with a flat, conical head that sits flush with the workpiece when tightened into a matching countersink.

Read definition
Standards

DIN standard

A German national standard issued by DIN, widely used to specify the shape and dimensions of fasteners.

Read definition
Pins & Rivets

Dowel pin

A cylindrical pin ground to a close tolerance, used to locate or align two parts and to carry shear load.

Read definition
Anchors

Drop-in anchor

A female-threaded expansion anchor set into a drilled hole, so a bolt or threaded rod can be installed after the anchor is fixed.

Read definition
Bolts

Eye bolt

A bolt with a looped eye at one end instead of a head, used as an attachment point for ropes, cables or lifting gear.

Read definition
Threads

Fine thread

A metric thread series with a smaller pitch than coarse for the same diameter, used where vibration, thin walls or adjustment matter.

Read definition
Bolts

Flange bolt

A hex bolt with an integrated flange under the head that spreads clamping load and can replace a separate washer.

Read definition
Washers

Flat washer

A flat ring placed under a bolt head or nut to spread the clamping load over a wider area and protect the joint surface.

Read definition
Materials

Galvanized steel

Steel that has been coated with zinc, by hot-dip galvanizing or electroplating, to resist corrosion.

Read definition
Standards

GB standard

The Chinese national standard system, in which GB/T denotes recommended standards and GB denotes mandatory ones.

Read definition
Bolts

Hex bolt

A bolt with a hexagonal head driven by a wrench or socket, the most common general-purpose fastener.

Read definition
Nuts

Hex nut

A six-sided nut turned with a wrench to clamp a joint on a bolt, stud or threaded rod.

Read definition
Finishes

Hot-dip galvanizing

A coating process in which a steel part is dipped in molten zinc, forming a thick, metallurgically bonded layer that protects it outdoors.

Read definition
Standards

ISO standard

An international standard published by ISO, used as the common reference for fastener dimensions, tolerances and mechanical properties.

Read definition
Washers

Large washer

A flat washer with an outside diameter larger than a standard washer, used to cover oversize or slotted holes and spread load on soft materials.

Read definition
Screws

Machine screw

A small screw with a uniform machine thread, used with a nut or a tapped hole rather than to cut a thread of its own.

Read definition
Finishes

Mechanical plating

A coating process that bonds zinc or zinc-alloy powder to steel by tumbling the parts with glass beads and a promoter, producing a ductile, uniform layer.

Read definition
Nuts

Nylon lock nut

A hex nut with a nylon insert that grips the bolt thread and resists loosening from vibration.

Read definition
Finishes

Passivation

A chemical treatment that removes free iron from a stainless steel surface and restores its passive oxide layer to improve corrosion resistance.

Read definition
Quality

Proof load

The tensile load a fastener must withstand without permanent deformation, used as an acceptance test for a strength class.

Read definition
Standards

Property class

A two-number class marked on a bolt, screw or stud that sets its nominal tensile strength and yield strength.

Read definition
Nuts

Rivet nut

A tubular nut installed by deforming its shank into a sheet, giving a load-bearing thread in thin material.

Read definition
Screws

Self-drilling screw

A screw with a drill point that drills its own hole, forms a thread and fastens in one operation.

Read definition
Screws

Self-tapping screw

A screw that forms or cuts its own thread in a pre-drilled hole in sheet metal, plastic or wood.

Read definition
Screws

Set screw

A headless screw, usually driven with a hex key, that locks a hub, collar or other part against a shaft or inside a threaded hole.

Read definition
Screws

Socket head cap screw

A screw with a cylindrical head and an internal hex socket, tightened with an Allen key and used where a strong, compact, recessed fastening is required.

Read definition
Pins & Rivets

Spring pin

A hollow, split cylindrical pin that compresses as it is driven into a hole and holds itself in place by spring force.

Read definition
Washers

Spring washer

A split, dished washer that stores elastic energy and is used to help keep a bolted joint from loosening under vibration.

Read definition
Nuts

Square nut

A four-sided nut with a square outline, offering a larger bearing area and a more traditional look than a hex nut.

Read definition
Materials

Stainless steel 304

A common austenitic stainless steel, also known as A2 or 18-8, used for fasteners where corrosion resistance matters more than high strength.

Read definition
Bolts

T-bolt

A bolt with a T-shaped head that slides into a T-slot or channel and locks when the nut is tightened.

Read definition
Quality

Tensile strength

The maximum stress a fastener can carry in tension before it fractures, usually expressed through a property class or in megapascals.

Read definition
Threads

Thread pitch

The axial distance between adjacent thread crests, expressed in millimetres for metric threads.

Read definition
Bolts

Threaded rod

A length of round bar threaded along its full length, used to join parts, set anchors or support pipework.

Read definition
Standards

Tolerance class

The permitted range of dimensional and thread deviation for a fastener, expressed as a product grade or a thread tolerance band.

Read definition
Bolts

U-bolt

A U-shaped bolt threaded at both ends, used with a saddle or plate and two nuts to clamp pipes, rods or tubes.

Read definition
Anchors

Wedge anchor

A mechanical anchor for concrete in which a tapered wedge expands a clip against the hole wall as the nut is tightened.

Read definition
Nuts

Weld nut

A nut designed to be welded onto a sheet or plate so that a thread is available where the material cannot be tapped.

Read definition
Screws

Wood screw

A screw with a tapered shank, coarse thread and sharp point that cuts its own path into timber instead of threading into a tapped hole.

Read definition
Finishes

Zinc plating

An electroplated zinc coating that gives steel fasteners moderate corrosion protection with a thin, uniform finish.

Read definition

Glossary

Need a standard or material checked?

Send the drawing or specification and we will confirm the exact standard, material and supply conditions.